Skip to content

Licensed Florida plumbing contractor · FL License CFC1426077 Mon–Fri open 24 hours. Sat 9 AM–5 PM. Sun closed. Emergency calls are taken 24/7.

Serving Sarasota, Florida 5.0 / 5.0 Google · 25 reviews

info@tkplumbing941.com

Ellenton · Manatee County

Toilet Repair and Installation in Ellenton, FL Homes

Toilets fail in predictable ways: they run, they rock, they leak at the base or they clog too often. TK Plumbing fixes all of those in Ellenton homes, and we install new toilets chosen for how you live, whether that means a taller bowl that is easier on the knees or a model that uses less water.

Comfort-height toilet installed in a bathroom in Ellenton, FL

The usual suspects

A toilet that refills by itself every so often has a leaking flapper or a fill valve set too high, letting water spill into the overflow tube. Mineral deposits from the local water stiffen flappers and crust valve seats, so this is one of the most common repairs we make. A few drops of food coloring in the tank will show you: if color appears in the bowl without flushing, the flapper is leaking.

A toilet that rocks has usually loosened at its closet bolts, and rocking breaks the wax seal underneath. Water seeping out at the base, staining on the floor, or a sewer smell in the bathroom all suggest the seal has failed. Tightening the bolts on a toilet that has already been rocking rarely fixes it; the toilet has to be pulled and reset on a new seal.

Manufactured homes have their own quirks

In the manufactured-home communities around Ellenton, toilets sit on a wood subfloor rather than concrete. A slow leak at the seal can soften that floor around the flange over time, and you may feel a slight give when stepping near the toilet. When we pull a toilet in one of these homes, we check the flange and the floor beneath it. A cracked or loose flange can be repaired with a reinforcing ring; a soft subfloor should be dealt with before a new toilet goes down, or it will rock again.

Rough-in measurements can also be different in older manufactured homes and in some older site-built houses, so we measure from the wall to the flange before you buy a replacement.

Picking a new toilet

  • Comfort height: a seat closer to standard chair height, which many residents in the area's 55+ communities find easier to use
  • Elongated or round bowl: elongated is more comfortable, round fits tight half-baths
  • Water use: modern toilets flush with far less water than models from earlier decades
  • One-piece or two-piece: one-piece units are easier to clean around, two-piece are often less expensive
  • Skirted bases: smooth sides with no exposed trapway, simpler to wipe down
  • Bidet seats: we can add a nearby supply valve and, where needed, coordinate with an electrician for a powered seat

How a replacement goes

We shut the water, drain and remove the old toilet, scrape the flange clean and inspect it, then set the new bowl on a fresh seal with new bolts. A new braided supply line and, if the old one is stiff or corroded, a new shutoff valve go in at the same time. We flush repeatedly and check for leaks at every connection. The old toilet leaves with us.

Tips for owners who come and go

If you close up an Ellenton home for the summer, shut the water off at the main. Water left sitting in a tank for months can leave a mineral ring and dry out the flapper, so plan to flush each toilet a few times when you return and listen for one that keeps running. If someone checks your home while you are gone, ask them to flush the toilets and run the taps so traps do not dry out and let sewer gas in.

Call TK Plumbing at 941-392-3846, license CFC1426077, for toilet repair or installation.

Ellenton questions

Is a running toilet worth fixing right away?

Yes. A constantly running toilet can waste a surprising amount of water and shows up on the bill. The repair is usually a flapper or fill valve, which is quick and inexpensive.

The floor feels soft by my toilet in a manufactured home. What should I do?

Have it checked soon. Softness usually means a long-term leak at the seal has damaged the subfloor. The flange and floor need to be sound before the toilet is reset.

How do I know what size toilet to buy?

Measure from the finished wall behind the toilet to the center of the bolts at the base. Most homes are at one standard measurement, but older homes may differ, so measure before you shop or let us check.

Call 941-392-3846 · 24/7